Search:

Type: Posts; User: Seppo




Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: Vats delete

    by Seppo
    Replies
    16
    Views
    14,523

    The resistor "fix" only works if it really is the...

    The resistor "fix" only works if it really is the key reader failing. I had to ground the relay on my 99 TA. Literally, I have a small wire grounded to the body running into the fuse/relay box that...
  2. Replies
    5
    Views
    1,584

    cammed 5 spd.... It vibrated the whole freaking...

    cammed 5 spd.... It vibrated the whole freaking car at idle. I was lucky enough to find a 1le tranny mount. I have poly motor and trans mounts for my TA, but I've never gotten around to installing...
  3. Replies
    5
    Views
    1,584

    I'ld just knock the rust off the UPHB and repaint...

    I'ld just knock the rust off the UPHB and repaint it.

    The v6 sway bar end links are weak sauce. The v8's had a poly type end link. Take off bars and end links would be a good budget solution. ...
  4. Replies
    11
    Views
    3,972

    Mind me asking what vendor you got them through?

    Mind me asking what vendor you got them through?
  5. Replies
    28
    Views
    11,575

    So um, 2.5 yrs later.... I finally put in the...

    So um, 2.5 yrs later.... I finally put in the frost king rolls I bought. I did the trunk well almost up to the stock plastic foot well at the front. Definite difference in exhaust noise inside the...
  6. Replies
    6
    Views
    778

    This.

    This.
  7. Thread: Lowering PHB

    by Seppo
    Replies
    9
    Views
    2,695

    "The advantage of the Panhard rod is its...

    "The advantage of the Panhard rod is its simplicity. Its major disadvantage is that the axle must necessarily move in an arc relative to the body, with the radius equal to the length of the Panhard...
  8. That is impressive. But dang that was a chit...

    That is impressive. But dang that was a chit load of work.
  9. Replies
    7
    Views
    950

    Sorry. I often only read the lounge since I no...

    Sorry. I often only read the lounge since I no longer have my v6. It seems alot of the old school crowd does the same.
  10. If you have to ask, I'm not sure you should be...

    If you have to ask, I'm not sure you should be attempting to do it yourself. Or if mechanic told you they have to, do not let them touch your car!
  11. Replies
    7
    Views
    950

    On the ls1 the engine ground was on the drivers...

    On the ls1 the engine ground was on the drivers side. It was a flat breaded wire about 3/8 inch wide, went from the block to the frame. I don't remember where it was on the 3.8.
  12. Replies
    7
    Views
    950

    I had this issue with my TA, but not quite that...

    I had this issue with my TA, but not quite that bad. I upgraded the grounds and it helped a bunch. After I installed a cam and paid to have it tuned, I have zero issues with this.

    Thread from...
  13. Replies
    23
    Views
    4,879

    Jealous am I. I want a 2nd gen 'bird.

    Jealous am I. I want a 2nd gen 'bird.
  14. Replies
    10
    Views
    3,837

    basically.... You definitely don't need to...

    basically.... You definitely don't need to disconnect the feed and return lines. If you need more room to work with you can wiggle the fuel rail out from behind the intake and over the alternator. ...
  15. Replies
    10
    Views
    3,837

    disconnect plug wires from coils to move aside...

    disconnect plug wires from coils to move aside
    disconnect injector wiring
    unbolt fuel rail
    pop out fuel rail and injectors
    drain fuel rail via schrader value
    remove c clips
    pop out injectors
    ...
  16. Replies
    20
    Views
    3,245

    Please pm me the price of 15684... Thanks!

    Please pm me the price of 15684... Thanks!
  17. Replies
    24
    Views
    7,993

    I'm pretty sure I ran 14.0x on street tires. I'ld...

    I'm pretty sure I ran 14.0x on street tires. I'ld have to search through old post to find out exactly.

    Didn't Shawn run like 13.8 on street tires? I also feel like someone with a turbo ran low...
  18. Replies
    3
    Views
    1,216

    9.8 on a 2.3 60' is actually pretty decent. 60'...

    9.8 on a 2.3 60' is actually pretty decent. 60' is huge in drag racing. If you can cut a 2.0x or low 2.1x, thats easily a 9.5.

    Its a heavy car for 200 hp.
  19. Replies
    30
    Views
    8,012

    Looking good! Polish the T-Stat elbow next?

    Looking good!

    Polish the T-Stat elbow next?
  20. Replies
    30
    Views
    8,012

    - !wire mod for the wire loom over the passenger...

    - !wire mod for the wire loom over the passenger front wheel.
    - polish the ac condenser, although you have to do it some what frequently
    - polish the brake lines out of the abs block
    - paint the...
  21. Replies
    22
    Views
    14,376

    Just an fyi, but... I still had issues with the...

    Just an fyi, but... I still had issues with the vats even after adding the resistor. I ended up grounding the relay in the fuse box under the hood. Every once in a while the security light comes...
  22. Replies
    26
    Views
    7,663

    I ran a spec stage 3 in my v6, with a resurfaced...

    I ran a spec stage 3 in my v6, with a resurfaced stock flywheel. It was grabby, and stiffer in the pedal. It was fine for DD, but was kind of a pita for long periods of stop and go traffic. Never...
  23. Replies
    18
    Views
    1,343

    Your not splicing into the hot wires, your...

    Your not splicing into the hot wires, your tapping into the grounds. The switch allows you to manually ground the hi or low fans to turn them on.

    I had the fan switch under the hood to use at...
  24. Replies
    8
    Views
    2,180

    firebird96 - Could be a pita to get that brake...

    firebird96 - Could be a pita to get that brake pad off. ;) Otherwise, it looks sharp!
  25. It bolts to the trans, and the hydralics go out...

    It bolts to the trans, and the hydralics go out through the bell housing.

    Either disconnect the slave, or I'm trying to remember the trick to unbolting the slave without disconnecting it.

    I...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4