Search:

Type: Posts; User: SlasherVRGR




Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    32,500

    Also on a side note, any time you mill heads,...

    Also on a side note, any time you mill heads, change heads, or change rockers you should measure pushrods to be sure they're the right length.

    Sent from my HTC6525LVW using Tapatalk
  2. Replies
    6
    Views
    32,500

    That would depend alot on the cam, duration plays...

    That would depend alot on the cam, duration plays more of a factor than lift. Best way would be to do some measurements and go from there.

    Sent from my HTC6525LVW using Tapatalk
  3. Could be a bent pushrod, collapsed lifter, bent...

    Could be a bent pushrod, collapsed lifter, bent valve or a valve stuck open some how aswell. Second vid sounds top end like to me.

    Sent from my HTC6525LVW using Tapatalk
  4. Replies
    4
    Views
    27,717

    I don't believe the bore spacing is the same...

    I don't believe the bore spacing is the same between the 60* and 3800 series engines.

    Sent from my HTC6525LVW using Tapatalk
  5. Replies
    13
    Views
    1,516

    It'll run fine, speedo will just be off. I had...

    It'll run fine, speedo will just be off. I had 3.73s in my bolt on 3800 car. They were nice.

    If it was an auto car I'd stay away from gears unless you've already done a stall, stall converter is...
  6. Replies
    8
    Views
    5,011

    You may consider 4.10 or 4.56s with the t-56. I...

    You may consider 4.10 or 4.56s with the t-56. I know alot of the ls1 and lt1 guys say 4.10 is the perfect gear for a daily. Both 5th and 6th are OD gears and 6th gear is way out there even with the...
  7. Replies
    5
    Views
    2,815

    Noice! I can honestly say I've never seen a...

    Noice! I can honestly say I've never seen a sixxer with a stand up like the turbo ls or lt guys do. Good work!

    Sent from my HTC6525LVW using Tapatalk
  8. Replies
    14
    Views
    9,177

    I believe he's saying you won't need injectors...

    I believe he's saying you won't need injectors for those mods. Its a pain to over inject a car. It doesn't get as good of gas mileage, and it makes tuning more difficult.
  9. Replies
    25
    Views
    11,072

    Jesus dude lol What actually caused the broken...

    Jesus dude lol

    What actually caused the broken block?
  10. Replies
    2
    Views
    17,630

    Have you checked trans fluid? My s10 kicks out...

    Have you checked trans fluid? My s10 kicks out and back into od at around 40-65 when its low on fluid.
  11. Wonder if anyone has used the intake from a fwd...

    Wonder if anyone has used the intake from a fwd and flipped it around on a rwd 3800.. something tells me it would be good for an N/A car.
  12. Thread: 3.73 gears

    by SlasherVRGR
    Replies
    2
    Views
    1,961

    I have had 2 sets of the cheapies from rock auto,...

    I have had 2 sets of the cheapies from rock auto, they both have whined a little bit. Strength won't matter in a 3.8 unless you're pushing more than an ls1 does(my second set is in my 98 z28 and...
  13. Replies
    6
    Views
    19,171

    The lower A-arms(front lower control arms) bolt...

    The lower A-arms(front lower control arms) bolt directly to the k member. I keep referring to them as A arms because most people call the rear control arms LCAs, or lower control arms. I didn't want...
  14. Replies
    7
    Views
    2,263

    Honestly those seal in a cans are all just a...

    Honestly those seal in a cans are all just a bandaid solution and can often times do more harm then good in the long run.

    If it solidifies enough to seal a leak, what's stopping it from chunking...
  15. Thread: Low Oil?

    by SlasherVRGR
    Replies
    4
    Views
    1,636

    To play devils advocate here, if you're driving...

    To play devils advocate here, if you're driving down the freeway and you run so low on oil that the light comes on, odds are you've already or will soon there after do damage. On my car the wire got...
  16. Replies
    5
    Views
    2,508

    Kris is right, the ls1s have really crappy PCV...

    Kris is right, the ls1s have really crappy PCV systems that constantly suck oil into the intake on wot.

    Same principle can be applied to your car, just a failing part instead of a poorly designed...
  17. Replies
    2
    Views
    628

    Hey there!

    Hey there!
  18. Replies
    6
    Views
    19,171

    The strut has nothing to do with alignment on...

    The strut has nothing to do with alignment on these cars, its not really a strut as it does no structural support. Odds are the lower a arm or k member are tweaked. Mine was on my z28 that got...
  19. Replies
    7
    Views
    2,263

    Could be the sender going out, even so 30 psi at...

    Could be the sender going out, even so 30 psi at idle isn't all that bad man. Good rule of thumb is 10 psi per 1000 rpm.
  20. Replies
    1
    Views
    415

    Do you push down on the knob then to go from...

    Do you push down on the knob then to go from park-back?
  21. Replies
    211
    Views
    243,633

    You ganna put the plates on the z? My z28 has...

    You ganna put the plates on the z?

    My z28 has a v6f-body.com sticker on it lol
  22. Replies
    2
    Views
    3,940

    Cheapest way I've found on my ls1 car is obd2...

    Cheapest way I've found on my ls1 car is obd2 Bluetooth dongle and torque pro app. Cost me a whopping 30$ including the app, I can see all kinds of stuff.

    Knock retard
    Timing advance
    Misfires...
  23. Replies
    4
    Views
    1,899

    Poll: The temp issue sounds like what my 3.4 bird would...

    The temp issue sounds like what my 3.4 bird would do when the water pump went out.

    The fins on the pump were worn down to nubs and it wouldn't push enough water unless I got on it a little bit.
    ...
  24. Replies
    5
    Views
    4,502

    I have 3.73s in mine, its a slight difference. I...

    I have 3.73s in mine, its a slight difference. I plan on a 3600 stall and some internal work over the summer hopefully
  25. Replies
    5
    Views
    4,502

    [emoji14] stall?

    [emoji14] stall?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4