Search:

Type: Posts; User: Turningfast




Page 1 of 20 1 2 3 4

Search: Search took 0.11 seconds; generated 10 minute(s) ago.

  1. Replies
    8
    Views
    42,640

    Lol, Larry is a big tease!!

    Lol, Larry is a big tease!!
  2. Replies
    3
    Views
    29,551

    You can change speed and rpm when it will shift...

    You can change speed and rpm when it will shift with hptuners, as well as lock up.
  3. FWIW, do 80# injectors. Keep timing sort of low,...

    FWIW, do 80# injectors. Keep timing sort of low, use boost to make up for it. Great turbo, I use a gt3582 with bb center. I would possibly go to the 1.something ar housing if I were you. I am...
  4. Replies
    17
    Views
    9,420

    Lol.

    Lol.
  5. Replies
    3
    Views
    3,956

    Also don't even worry about new map sensor, don't...

    Also don't even worry about new map sensor, don't need it.
  6. Replies
    3
    Views
    3,956

    It has nothing to do with bar, but when the maf...

    It has nothing to do with bar, but when the maf sensors range is maxed out. You can use a maf scaler or change the tune so the PCM does not cut fuel when it maxes. After it maxes it will go off of...
  7. Replies
    25
    Views
    10,861

    http://i617.photobucket.com/albums/tt260/turningfa...

    http://i617.photobucket.com/albums/tt260/turningfast/five0-ouch_zpsf437010e.gif
  8. Replies
    10
    Views
    16,207

    Sticky: Lol, wut?

    Lol, wut?
  9. Replies
    2
    Views
    1,371

    Do a compression test to find what cyl is borked...

    Do a compression test to find what cyl is borked up, and go from there. Sounds like a dropped valve
  10. Thread: New

    by Turningfast
    Replies
    7
    Views
    3,244

    Your best bet is to get lucky and have cash ready...

    Your best bet is to get lucky and have cash ready to go when someone is selling a set up. It's pretty expensive to piece together a kit unless you use the cheap eBay stuff.
  11. Oh, my bad! I was retarded and gave measurements...

    Oh, my bad! I was retarded and gave measurements for the rwd trans. I don't read too good, lol.
  12. I have a trans sitting around. It's about 31 1/4...

    I have a trans sitting around. It's about 31 1/4 inches long, plus the .5 inch the output shaft sticks out, this is with the bell housing. Bell housing where it bolts to the block as about 16.5"...
  13. Replies
    11
    Views
    2,832

    First thing I would do is put a vacuum gauge on...

    First thing I would do is put a vacuum gauge on it and drive it. If its a clogged cat it will have 0 vacuum, and possibly positive pressure when it will not accelerate. Does it hav a check engine...
  14. Replies
    11
    Views
    2,832

    Could be a clogged cat, or 100 other things.

    Could be a clogged cat, or 100 other things.
  15. Replies
    7
    Views
    2,361

    Oops, sorry. I assumed you were turbo because of...

    Oops, sorry. I assumed you were turbo because of your oil pan thread in the fi section.
  16. Replies
    7
    Views
    2,361

    If you can data log see what cyl it is. Spray...

    If you can data log see what cyl it is. Spray that wire down with water at idle with a spray bottle and see if it starts missing. Most likely it is a bad wire that is burnt or leaking voltage. I...
  17. Replies
    3
    Views
    1,730

    Like he said. The only thing I will add is you...

    Like he said. The only thing I will add is you will need to run a thread chaser in some of the accessory holes in the fwd, the power steering pump holes and I think some of the A/C stuff. This is...
  18. Replies
    11
    Views
    3,078

    Nice.

    Nice.
  19. Thread: true duals

    by Turningfast
    Replies
    26
    Views
    21,964

    Make your own gaskets, they will be the cheapest,...

    Make your own gaskets, they will be the cheapest, most reliable ones. Go to an art store and get a roll of thin copper, then go to an auto parts store and get some copper rtv. cut out 3 or 4 copper...
  20. Replies
    13
    Views
    4,294

    another one...

    another one
    http://www.fullthrottlev6.com/forums/showthread.php?71205-Turbo-support-bracket
  21. Replies
    13
    Views
    4,294

    2.5" is kind of large, but using a production...

    2.5" is kind of large, but using a production header you are kind of stuck with it. My junk uses 2" collectors and a 2" crossover. I figured if ls based engines can make 1k hp with 2 1/4, 2" would...
  22. Replies
    13
    Views
    4,294

    Brace the turbo well and use a turbo safe...

    Brace the turbo well and use a turbo safe flexpipe on the crossover pipe between the left and right side.
  23. Replies
    13
    Views
    4,294

    There is a ton of info if you read through the...

    There is a ton of info if you read through the forced induction part of the board.
    Here is one thread from there, has a lot of info about using power logs and gtp manifolds. There are others if...
  24. Thread: true duals

    by Turningfast
    Replies
    26
    Views
    21,964

    Over axle is really easy with anpanhard bar...

    Over axle is really easy with anpanhard bar relocation kit.
  25. Replies
    11
    Views
    3,078

    Looks an, that is huge if it is more than -10,...

    Looks an, that is huge if it is more than -10, you will have to check if it will fit on the front of the pan where I have mine. Just make sure to mock it up to see if you will clear the crank pulley...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4