Search:

Type: Posts; User: LuminousX




Search: Search took 0.00 seconds.

  1. Replies
    28
    Views
    5,228

    man, I wired my wires wrong... I wasn't paying...

    man, I wired my wires wrong... I wasn't paying attention to the firing order I pulled from the internet, after I had that figured out it started, but I'm seeing bank 2 running super rich, only on...
  2. Replies
    28
    Views
    5,228

    things went from bad to worst, I removed all the...

    things went from bad to worst, I removed all the lifters, and push rod to see if any were bent or damaged, saw nothing wrong and decided to move on with replacing the intake manifold gasket upper,...
  3. Replies
    34
    Views
    2,447

    Are you running threw the side or all the way...

    Are you running threw the side or all the way back, it's a tight fit for 2.5" I would love to see if 3" can fit.
    which side did you run it on.
  4. Replies
    28
    Views
    5,228

    I've only been able to hit around the same 6psi,...

    I've only been able to hit around the same 6psi, I turned down/off the boost controller because it's untuned, I want to go with some 24lb injectors, but I spent last summer pretty much installing the...
  5. Replies
    28
    Views
    5,228

    The middle gauge is for the oil, my fuel gauge is...

    The middle gauge is for the oil, my fuel gauge is on the fuel rail, driving wise I have no problem with the car, the power is still their, it's just that with the A/F all over the place it's kinda...
  6. Replies
    28
    Views
    5,228

    I don't know what to do at this point, I've got...

    I don't know what to do at this point, I've got the lower, and upper intake removed, checked all the lifters, and they all seem to be the, looked at the intake valve that seemed to be intact as well...
  7. Replies
    28
    Views
    5,228

    here's a good one, after what seems like a whole...

    here's a good one, after what seems like a whole year has gone by, and me chasing after what I though was ignition problems, injector problems... all I had to do was remove the valve cover to see...
  8. I believe it was mostly the idle, which I did...

    I believe it was mostly the idle, which I did manage to bump it up a bit, and most of the rough idle went away, but I can tell here the misfire, even more now that the car idles higher.I was able to...
  9. I've Compared quite a few files, and they all...

    I've Compared quite a few files, and they all seems pretty much the same apart from the trans stuff, but I'm not sure if the trans part of the tune would cause it to run much worst then with the 96...
  10. hey do you have a tune file I can do some...

    hey do you have a tune file I can do some comparison on, the PCM I'm using came out of a 97, and so did the file, had no way of pulling, or using the 96 Manual file.
    the car also runs much better...
  11. NGK tr6, didn't check the gaps, but I see online...

    NGK tr6, didn't check the gaps, but I see online it says gapped to .039, I see some people online saying they don't come gapped, and I never checked them, rookie mistake?? not even sure if that would...
  12. I get the p0300 for sure, no cylinder, but I do...

    I get the p0300 for sure, no cylinder, but I do have hp tuners, and it showed that most of the misfire was on cylinder #2.
    I have the stock injectors, running a Quantum 255 aka HFP-343 no vacuum...
  13. 96 Camaro 3.8 Bad Injector, Burnt Valve, Bad Lifter

    little bit of back story, car had this misfire since I started my turbo build, drove the car no problem
    even with the misfire, always Idle smooth-ish, changed my plugs twice during the span of 3...
  14. Replies
    28
    Views
    5,228

    the way I ran my intercooler piping gave me no...

    the way I ran my intercooler piping gave me no choice but to relocate it to the rear, I took out everything that as to do with the ac, and got a shorter belt

    6286
    to run it like this you'll need...
  15. Replies
    28
    Views
    5,228

    UPDATE... the whole starting issue might be a...

    UPDATE...

    the whole starting issue might be a ignition switch going bad problem, if I cycle the key enough time during the whole starter clicking thing then it will turn over maybe the 2nd or 4th...
  16. Replies
    28
    Views
    5,228

    having a issue starting this car after moving the...

    having a issue starting this car after moving the battery to the rear, I've ran 0 gage pwr, and 2 gage gnd to 2 terminal post I've install where the battery was up front, starter clicks like crazy,...
  17. Replies
    28
    Views
    5,228

    did a short video on the car after taking it on...

    did a short video on the car after taking it on about a hour drive, a lots of traffic just to see how the temp will hold up, I do have my fans on a switch, so that does help...
    feel free to ask any...
  18. Replies
    28
    Views
    5,228

    yeah, that's what I intent to do in the near...

    yeah, that's what I intent to do in the near future, I will post some pictures of the build soon, maybe some folks can get ideas based on how I did mines...
  19. Replies
    28
    Views
    5,228

    I've gotten most of the turbo system put...

    I've gotten most of the turbo system put together, was told by someone at PCM for less that they could tune the 3.8l PCM
    only to ship it out, and then be told that they only tune the v8 LT1's.
  20. Replies
    28
    Views
    5,228

    found out that base on that turbo kit I have, I...

    found out that base on that turbo kit I have, I can just run it to the valve cover if I clocked it a little bit, and get some angle to drain.
    thanks for the reply thou.

    P.S the most time spend...
  21. Replies
    28
    Views
    5,228

    96 3.8L Turbo Build

    Good Day/Night

    Bought a Green Colored 96 Camaro with a 3.8L S II /w 5MT, that was about 2 year ago
    at this moment I have the timing chain cover off the car with the intention of drilling a hole,...
Results 1 to 21 of 21