Search:

Type: Posts; User: HeavyChevy3800




Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    7
    Views
    4,149

    Yes. Acceleration will be better with the non HD...

    Yes. Acceleration will be better with the non HD gear ratio. If I remember correctly the L36 and L67 converters are different diameters, have their own bolt patterns and different flex plates to...
  2. Replies
    7
    Views
    4,149

    It's been a while but I believe the HD...

    It's been a while but I believe the HD transmissons are a 2.93 ratio and then non HD are a 3.29 ratio. I would prefer the non HD ratio.
    I'm not sure about the 4T60E. Never messed with one .
  3. Replies
    8
    Views
    3,225

    The lim gaskets fail. They were oem plastic and...

    The lim gaskets fail. They were oem plastic and were known to warp and leak. There are new aluminum lower intake gaskets that work better.
  4. Replies
    7
    Views
    4,149

    The HD transmission has different gearing than...

    The HD transmission has different gearing than the non HD transmission . The L67 pcm will need to be flahed for the correct gearing if its going to run a non HD trans.
  5. Replies
    8
    Views
    3,472

    There was once an m112/m90 hybrid. You ran an m90...

    There was once an m112/m90 hybrid. You ran an m90 housing with the longer m112 rotors and shorter snout. Their were bullet adapters/spacers that went between the m90 housing and m112 snout.
  6. Replies
    2
    Views
    589

    Lining up the dots is the quick and easy way to...

    Lining up the dots is the quick and easy way to do it. 99% of people do it this way and they're fine. If you want to get 100% of potential out of the cam or get the exact degree advance or retard...
  7. Replies
    5
    Views
    2,288

    Ford 8.8 center with LS1 axle tubes. That was my...

    Ford 8.8 center with LS1 axle tubes. That was my plan for a cheap-o rear end.
  8. Bottom end is toast. You may just have to pull...

    Bottom end is toast. You may just have to pull the motor and tranny together.
  9. Thread: Help!

    by HeavyChevy3800
    Replies
    3
    Views
    1,341

    The SES light flashes when you are actively...

    The SES light flashes when you are actively having a misfire. Sounds like cylinder six is the problem. You need fuel, air, spark and compression for combustion to happen. I would start off with...
  10. Nitrous. It's cheap and easy. Sent from my...

    Nitrous. It's cheap and easy.

    Sent from my myTouch_4G_Slide
  11. Replies
    4
    Views
    975

    Kooks true duals. ...

    Kooks true duals.

    http://www.ws6project.com/user_stor/catalog/images/kooks.JPG
  12. http://www.teachamantofix.com/wp-content/uploads/2...

    http://www.teachamantofix.com/wp-content/uploads/2010/08/RightyTighty.jpg
  13. That seal is called your tail shaft seal. You'll...

    That seal is called your tail shaft seal. You'll have to remove the driveshaft to replace the seal. Replacing the two piece driveshaft with an aluminum one would be a good idea while you're in...
  14. Replies
    32
    Views
    12,559

    Yeah! ...

    Yeah!

    https://sphotos-a-atl.xx.fbcdn.net/hphotos-ash3/1173803_10200717525996202_1876245073_n.jpg
  15. Replies
    4
    Views
    2,881

    If she doesn't like it then just plastidip it.

    If she doesn't like it then just plastidip it.
  16. OEM MLS gaskets. No issues.

    OEM MLS gaskets. No issues.
  17. Replies
    4
    Views
    2,116

    You can get it from under the car with a few...

    You can get it from under the car with a few extensions and universal joint. You can get it from the top with tiny asian arms and the upper and lower intake off. Taking off the front motor mounts...
  18. Replies
    2
    Views
    1,790

    The ZEX box is fine for the WOT switch. I would...

    The ZEX box is fine for the WOT switch. I would prefer a window swith for the additional safety but you don't need it. With an Auto you'll be spraying through the shifts unless you let off and with...
  19. Replies
    5
    Views
    980

    Different brand oil pressure sensors read...

    Different brand oil pressure sensors read pressure differently. Have you tested the oil pressure with a mechanical gauge?
  20. Replies
    10
    Views
    6,555

    Looks great. Those are my favorite wheels on a...

    Looks great. Those are my favorite wheels on a Camaro.

    Sent from my myTouch_4G_Slide
  21. Replies
    254
    Views
    45,852

    Wait until it's machined to order bearings. You...

    Wait until it's machined to order bearings. You don't know how much it has to be machined for the surface to get cleaned up. L32/L67 rods go with L32/L67 pistons as L26/L36 rods go with L26/L36...
  22. Replies
    254
    Views
    45,852

    This guys has all kinds of used 3800 stuff. ...

    This guys has all kinds of used 3800 stuff.

    http://www.moradpartscompany.com/
  23. Replies
    254
    Views
    45,852

    I would run factory valves. Are you heads ported...

    I would run factory valves. Are you heads ported at all where you require larger diameter valves?

    I wouldn't recommend any of those coolers. You want a bar and plate cooler not a tube a fin...
  24. Replies
    8
    Views
    1,400

    So many cars run K&N filters and have no issues...

    So many cars run K&N filters and have no issues with their MAFs. The only way the oil is going to cause an issue is you clean and oil the filter and use way too much oil. You have to use enough...
  25. Replies
    16
    Views
    2,349

    The "True" Ram! ...

    The "True" Ram!

    http://files.myopera.com/sazdateli/albums/728139/Big%20Horn%20Ram,%20Rocky%20Mountain%20National%20Park,%20Colorado.jpg
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4