Series II & Series III Factory NA 3.8L Motors
Sticky Threads
This has been a much delayed project that I unfortunately haven't had the time to focus on. Moving forward I will keep this thread open for everyone...
This list covers every camshaft available for the GM 3800 Series II Engine. They are listed in increasing size starting with the STOCK cam. All...
http://users3.ev1.net/~black_ops/cams/VE%20calculator.xls Sheet 1 - compare two cams (forum post) this was an attempt to put _ in there to keep...
THE SYMPTOMS: poor idle, part throttle stumble, full throttle stumble, popping noises, solid illumniated "service engine soon" light, flashing...
I have noticed a few more cam related questions popping up on the forums and figured i would throw this up here as a bit of information before you...
I have continued the assistance to everyone by gathering a list of the board members who have installed aftermarket cams. Supporting mods are...
Normal Threads
Hey everyone I've got my firebird and I'm trying to find a turbo to put on the stock 3800 series 2 I've seen some people advertising for a T4 turbo...
So Ive got the aussie manifold all cleaned up, fitted her in the car. I'm using an intake elbow from a commodore ,along with a custom adapter to...
Gday all, hope your well. Putting a L36 3.8L into a '78 Toyota Stout, and have a few questions. The motor's an ecotech out of a '03 Holden VY...
Hello looking for some help with torque spec's for my 3800 Series III upper and lower intake the upper is aluminum as well as the lower and i can...
Witness in Trump Impeachment Found Dead
So after doing a small build and overhaul on my 2000 firebird 3.8 I can't get it to start. Here is a list of everything I've tested on my 3.8...
I've read this forum up and down, and theres a good deal of information about physically turboing a 3.8, but not a lot on parts used and whatnot. ...
Does anyone off the top of their head know the type of slip yoke that goes into the t5 in our 3.8l? I had a leak and just tried replacing the...
So for my 3800 build for my 2000 Camaro, I've ordered the stroker kit from mace engineering in Australia. Once it gets here I'll be sending the...
Hey guys, So I just purchased a 1998 3.8 5 speed. I have spent the past couple of weeks running through and fixing all the issues besides a...
Hello this is my first post on any forum so please bare with me. I have a 99 Camaro v6 just blew the motor. Here is my plan so far, use a l67 block...
Just looking for some input from anyone who has used the ARH n/a cam. This car will probably never see the track, so I really don't care about top...
Hey guys. About two weeks ago both my knock sensors went. Got them both replaced with new pigtails and now the passenger side is fine but the driver...
My first question is what other filters fit on our cars? I searched a few times on this forum to find nothing. I'm curious if there are larger...
Hi All, new member here. I have a 2002 firebird with the L36 engine. Has rod knock so decided to purchase a used motor. Got it, disassembled and...
COWBOYS VS TEXANS Live Streaming Dallas Cowboys vs Houston Texans Live Streaming Cowboys vs Texans Live Streaming
Titans vs Bills Live Streaming Dolphins vs Bengals Live Streaming Panthers vs Giants Live Streaming Ravens vs Browns Live Streaming
dfsafdsfd/sgds gd.sg/dsg dsg/ds/gds g/dsg/ds gd/sg/dsg ds/g/dsg we/ds/gd sgd/sg/ds/dsdsfd
Has anyone adjusted the cam timing with a stock cam? I bought a rollermaster timing chain and I'm wondering if it would be better to advance the cam...
anyone know where i could get 11:1 pistons for my 3800 from ? without having to sell a kidney first ?... im not going to be running any nitrous, just...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
